Netsh commands for Interface IP

You can run these commands from the Windows XP command prompt or from the command prompt for the Netsh Interface IP context. For these commands to work at the Windows XP command prompt, you must type netsh interface ip before typing commands and parameters as they appear in the syntax below. To run these Netsh commands on a remote Windows 2000 Server, you must first use Remote Desktop Connection to connect to a Windows 2000 Server that is running Terminal Server. There might be functional differences between Netsh context commands on Windows 2000 and Windows XP.

For more information on Netsh, see Using Netsh

To view the command syntax, click a command:

set address

Configures an IP address and a default gateway on a specified interface.

Syntax

set address [name=]InterfaceName [source=]{dhcp | static [addr=]IPAddress [mask=]SubnetMask [gateway=]{none | DefaultGateway [[gwmetric=]GatewayMetric]}}

Parameters

[name =] InterfaceName : Required. Specifies the name of the interface for which you want to configure address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[source=]{dhcp | static [addr=]IPAddress [mask=]SubnetMask [gateway=]{none | DefaultGateway [[gwmetric=]GatewayMetric]}} : Required. Specifies whether the IP address to configure originates from a Dynamic Host Configuration Protocol (DHCP) server or is static. If the address is static, IPAddress specifies the address to configure, and SubnetMask specifies the subnet mask for the IP address being configured. If the address is static, you must also specify whether you want to leave the current default gateway (if any) in place or configure one for the address. If you configure a default gateway, DefaultGateway specifies the IP address of the default gateway to be configured, and GatewayMetric specifies the metric for the default gateway to be configured.

/?: Displays help at the command prompt.

Remarks

•	You can use this command to switch an interface between DHCP configuration and static configuration. If the interface is configured statically, the DNS and WINS server addresses for this interface must also be statically configured.
•	Omitting the DefaultGateway parameter does not clear gateway configuration but preserves whatever was previously configured.

add address

Adds an IP address and a default gateway on a specified interface configured with a static IP address.

Syntax

add address [name=]InterfaceName [addr=]IPAddress [mask=]SubnetMask [[gateway=] DefaultGateway [gwmetric=]GatewayMetric]

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to add address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[addr=]IPAddress [mask=]SubnetMask : Required. Specifies the IP address to add and the subnet mask for that IP address.

[gateway=]DefaultGateway [gwmetric=]GatewayMetric : Specifies the IP address of the default gateway to add and the metric for that default gateway.

/?: Displays help at the command prompt.

delete address

Deletes an IP address or a default gateway on a statically configured interface.

Syntax

delete address [name=]InterfaceName [addr=] IPAddress [[gateway=]{DefaultGateway | all}]

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to delete address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[addr=]IPAddress : Required. Specifies the IP address to delete.

[gateway=]{DefaultGateway | all} : Specifies whether to delete one default gateway or all default gateways. If only one default gateway should be deleted, DefaultGateway specifies the IP address of the default gateway to be deleted.

/?: Displays help at the command prompt.

Remarks

•	This command will not delete the last IP address on the interface.

show address

Displays information about static IP addresses and default gateways on a specified interface. Used without parameters, show address displays address information for all interfaces.

Syntax

show address [[name=]InterfaceName]

Parameters

[name=]InterfaceName : Specifies the name of the interface for which you want to display address information. The InterfaceName must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

/?: Displays help at the command prompt.

Remarks

•	For interfaces configured using DHCP, use the ipconfig command to display the assigned IP addresses, lease parameters, and other DHCP information.

set dns

Configures a DNS server address for a specified interface.

Syntax

set dns [name=]InterfaceName [source=]{dhcp | static [addr=]{DNSAddress | none}} [[ddns=]{disabled | enabled}] [[suffix=]{interface | primary}]

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to set DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[source=]{dhcp | static [addr =]{DNSAddress | none}} : Required. Specifies whether the IP address of the DNS server is configured by DHCP or is static. If the IP address is static, DNSAddress specifies the IP address of the DNS server to configure, and none specifies that the DNS configuration should be removed.

[ddns=]{disabled | enabled} : Specifies whether the computer should attempt DNS dynamic update registration of the IP addresses of this connection and the full computer name. The full computer name is specified in the Control Panel item System on the Computer Name tab. The enabled parameter specifies that the attempt should occur. The disabled parameter specifies that the attempt should not occur.

[suffix=]{interface | primary} : Specifies whether the computer should attempt DNS dynamic update to register the IP addresses and the connection-specific domain name of the specified connection in addition to the full computer name. The connection-specific DNS name of this connection is the concatenation of the computer name (which is the first label of the full computer name) and the DNS suffix of this connection. The interface parameter specifies that both the full computer name and connection-specific name should be registered. The primary parameter specifies that only the full computer name should be registered.

/?: Displays help at the command prompt.

Remarks

•	If the interface is already statically configured, the static parameter replaces the existing list of DNS server addresses with the one specified in the command.
•	The default setting for ddns= is enabled.
•	The default setting for suffix= is primary.

add dns

Adds a DNS server to a list of DNS servers for a specified interface.

Syntax

add dns [name=]InterfaceName [addr=] DNSAddress [[index=]DNSIndex]

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to add DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[addr= ]DNSAddress : Required. Specifies the IP address of the DNS server to add.

[index=]DNSIndex : Specifies the position of the added DNS server in the list of DNS servers for the interface.

/?: Displays help at the command prompt.

Remarks

•	A lower number for the DNSIndex parameter corresponds to a higher preference. If no index is specified, then the server is added with the lowest preference.

delete dns

Deletes a DNS server or all DNS servers from a list of DNS servers for a specified interface or for all interfaces.

Syntax

delete dns [name=]InterfaceName [addr=]{DNSAddress | all}

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to delete DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[addr=]{DNSAddress | all} : Required. Specifies whether to delete the address of one DNS server or all servers for all interfaces. If only one DNS server should be deleted, DNSAddress specifies the IP address of the DNS server to delete.

/?: Displays help at the command prompt.

show dns

Displays the DNS configuration of a specified interface. Used without parameters, show dns displays the DNS configurations of all interfaces.

Syntax

show dns [[name=]InterfaceName]

Parameters

[name=]InterfaceName : Specifies the name of the interface whose DNS configuration you want to display. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

/?: Displays help at the command prompt.

set wins

Sets WINS server configuration to either DHCP or static mode for a specified interface.

Syntax

set wins [name=]InterfaceName [source=]{dhcp | static [addr=]{WINSAddress | none }}

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to set WINS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[source=]{dhcp | static [addr=]{WINSAddress | none }} : Required. Specifies whether the IP address of the WINS server to configure should be assigned by DHCP or is static. If the IP address is static, WINSAddress specifies the IP address of the WINS server to configure, and none specifies that the WINS configuration should be removed.

/?: Displays help at the command prompt.

Remarks

•	If the interface is already statically configured, the static parameter replaces the existing WINS server address list with the one specified in the set wins command.

add wins

Adds a WINS server to a list of WINS servers for a specified interface.

Syntax

add wins [name=]InterfaceName [addr=] WINSAddress [[index=]WINSIndex]

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to add WINS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[addr=]WINSAddress : Required. Specifies the IP address of the WINS server to add.

[index=]WINSIndex : Specifies the position of the added WINS server in the WINS server list for that interface.

/?: Displays help at the command prompt.

Remarks

•	A lower number for the WINSIndex parameter corresponds to a higher preference. If no index is specified, then the server is added with the lowest preference.

delete wins

Deletes a WINS server or servers from a list of WINS servers for a specified interface or all interfaces.

Syntax

delete wins [name=]InterfaceName [addr=]{WINSAddress | all}

Parameters

[name=]InterfaceName : Required. Specifies the name of the interface for which you want to delete a WINS server or servers. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").

[index=]InterfaceIndex : Specifies the interface index, an integer that identifies the interface.

[rr=]RefreshRate : Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).

/?: Displays help at the command prompt.

Remarks

•	To obtain the interface index for an interface, review the output of the show interface command used without parameters.

show ipaddress

Displays information for a specified IP address. Used without parameters, show ipaddress displays information for all IP addresses on all interfaces once.

Syntax

show ipaddress [[index=]IPAddress] [[rr=]RefreshRate]

Parameters

[index=]IPAddress : Specifies an IP address of an interface.

[rr=]RefreshRate : Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).

/?: Displays help at the command prompt.

Remarks

•	To obtain the IP addresses of all interfaces, review the display of the show ipaddress command used without parameters.

Remarks

•	To obtain the IP addresses for all interfaces, review the display of the show ipaddress command used without parameters.

show tcpconn

Displays information on a specified TCP connection. Used without parameters, show tcpconn displays information for all TCP connections once.

Syntax

show tcpconn [[index=]{LocalIPAddress | LocalPort | RemoteIPAddress | RemotePort}] [[rr=]RefreshRate]

Parameters

[index=]{LocalIPAddress | LocalPort | RemoteIPAddress | RemotePort} : Specifies the connection about which to display information. The LocalIPAddress parameter specifies an IP address of an interface. The LocalPort parameter specifies a TCP port for a local process. The RemoteIPAddress parameter specifies an IP address of a remote host. The RemotePort parameter specifies a TCP port for a remote process.

[rr=]RefreshRate : Specifies the refresh rate (the number of seconds between refreshing the display of the information).

/?: Displays help at the command prompt.

show tcpstats

Displays TCP statistics. Used without parameters, show tcpstats displays the statistics once.

Syntax

show tcpstats [[rr=]RefreshRate]

Parameters

[rr=]RefreshRate : Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).

/?: Displays help at the command prompt.

show udpconn

Displays information about the UDP ports used for each IP address. Used without parameters, show udpconn displays UDP port information for all IP addresses once.

Syntax

show udpconn [[index=]{LocalIPAddress | LocalPort}] [[rr=]RefreshRate]

Parameters

[index=]{LocalIPAddress | LocalPort} : Specifies the connection about which to display information. The LocalIPAddress parameter specifies an IP address of an interface. The LocalPort parameter specifies a UDP port for a local process.

none

Remarks

•	To create a configuration script file, redirect the output of this command to a file.

Netsh Interface IP example

The following command configures the interface named Local Area Connection with the static IP address 10.0.5.99, the subnet mask of 255.255.255.0, and a default gateway of 10.0.5.1:

set address name="Local Area Connection" source=static addr=10.0.5.99 mask=255.255.255.0 gateway=10.0.5.1

Formatting legend

Format	Meaning
Italic	Information that the user must supply
Bold	Elements that the user must type exactly as shown
Ellipsis (…)	Parameter that can be repeated several times in a command line
Between brackets ([])	Optional items
Between braces ({}); choices separated by pipe (\|). Example: {even\|odd}	Set of choices from which the user must choose only one
Courier font	Code or program output

This entry was posted on Senen, Juni 7th, 2010 at 2:34 pm and is filed under Windows. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.

Trackback URI | Comments RSS